Alotofmanuals.com
user manuals database
Categories
Directory
Accusplit
Headphones
AE2700
Manual
AE2700 Guide
User manual for AE2700
Here is the user manual for AE2700. You can read and download this user guide for free. User's manual, provided by the manufacturer, allows you to use properly your home appliances and electronics.
PDF MODE
ORIGINAL MODE
1
1
Download User manual for AE2700
How to use our site?
Our goal is to provide you with an access to the content of the user manual and guide for AE2700. Using the online player, you can look through the content and go to the page where you will find the solution of your problems with AE2700.
For your convenience
If looking through the AE2700 user manual directly on our website is not convenient for you, there are two possible ways: You can use full-screen viewing mode. To start viewing the user manual for AE2700 on full screen, use the button fullscreen on our player. You can download the user manual for AE2700 to your computer and save it in your files.
Table of contents
Document Outline
A16R-SJ JBOD Task List
Step 1: Unpacking the JBOD System
Front Panel View (Closed)
Front Panel View (Open)
Rear View
Switch ID
2U-12R/U Chassis ID
Step 2: Mounting the JBOD System in a Rack
1. Attack eight rack nuts into the rack, making sure that they correspond with the mounting points on the rails.
2. Adjust the length of the rails as needed.
3. Secure the rails using two nuts and bolts on both the front and back posts of the rack.
4. Tighten the locking screws.
5. Slide the JBOD system into the rack and secure it into place using the fixing screws.
Using the Rail Extenders
1. Install the rail extenders and attach the screws to secure them.
2. Slide the RAID system into the rack and secure it into place using the fixing screws.
Step 3: Installing Disk Drives
SAS hard disks
1. Insert the SAS hard drive into the hard disk tray. Screw the sides to secure the hard disk. Repeat this procedure to install more hard disks.
2. Insert the key to the key slot and turn to unlock the front panel door.
3. Pull open the front panel door.
4. Insert the hard disk tray into the empty slot.
5. Push down the tray handle to secure the hard disk tray into place.
6. Repeat steps 4 to 5 until all the required disks have been installed.
7. Close the front panel door, then lock it.
SATA hard disks
1. Place the AA-MUX adapter on the hard disk tray and attach the four screws as shown.
2. Place the hard disk into the hard disk tray with the drive connectors facing the AA-MUX adapter.
3. Slide the hard disk towards the AA-MUX adapter and connect the power and data connectors.
4. Attach the screws to secure the hard disk.
5. Insert the hard disk tray into an empty slot.
6. Push down the tray handle to secure the hard disk tray into place.
7. Repeat steps 1 to 6 until all the required disks have been installed.
8. Close the front panel door, then lock it.
Step 4: Making Connections
1. Insert the SAS cable into the CH1 port of A16R-SJ.
2. To connect to a RAID system, insert the other end of the SAS cable to the EXP port of the RAID system(B). Or to connect to a host server, insert the other end of the SAS cable to the HBA connector of the host server (C).
Expanding JBOD Enclosures
Figure 1-1 RAID system with JBOD enclosure in a loop
1. Connect the RAID system EXP port to the CH1 port of the JBOD1 using a SAS cable.
2. To connect to the next JBOD, connect the EXP port of JBOD1 to the CH1 port of JBOD2.
3. Follow the same procedures to connect the succeeding JBOD enclosures.
4. To make a loop, connect the EXP port of JBOD3 to the CH1 port of JBOD2.
5. Connect the EXP port of JBOD2 to the CH1 port of JBOD1.
6. Connect the EXP port of the RAID system to the CH1 port of JBOD3.
7. Set the chassis ID:
Step 5: Powering on the System
Connecting the Power
1. Plug one power cable into the AC power port.
2. Plug the second power cable into the other AC power port.
3. Once all the components have been connected, the system can now be powered on using the power switch.
Step 6: Configuring the JBOD system
Configuring Host Server Connection
Figure 1-2 Host server connection with JBOD expansion
1. Open the folder with the installation files for Windows 32-bit or 64-bit.
2. To check the configuration, open Computer Management > Device Manager.
Configuring the RAID System
Figure 1-3 RAID system with JBOD expansion
1. Connect the RAID system and the JBOD enclusures following the procedures inExpanding JBOD Enclosures on page 19.
2. Connect the RAID system to the host server using fibre cables as shown.
3. Connect controller A and controller B of the RAID system to the LAN switch.
4. Connect the host server to the LAN switch.
• To configure using GUI
1. Connect and login to the GUI webpage.
2. Check if the status of all the hard disks are unused.
3. Create disk groups.
4. Create logical disks.
5. Create LUN mapping.
• To configure using CLI
1. Login to the CLI utility.
2. Check the hard disk condition, type hddlist all in the command line (CLI>).
3. Create disk groups using the dgcreate command.
4. Create logical disks using the ldcreate command.
5. Create LUN mapping using the htpaddlun command.
6. Check if all logical disks have LUN mapping, type htplistlun all in the command lin
Step 7: Host Configuration
Windows Multi-Path Solution: Pathguard
• To install Pathguard:
1. Double click the installation files on a host computer (choose Windows 32-bit or 64-bit installation file according to your host system). Installing Pathguard will automatically install the MPIO driver.
2. Follow the installation wizard to start installation.
3. After installing Pathguard utility, click Next to continue installing the MPIO driver.
4. Reboot the computer to complete installation.
• To check disk configuration:
1. Go to Computer Management > Device Manager.
2. Go to Disk Management, and check for the two installed disk devices to indicate the system is successfully connected.
Step 8: Powering Off the System
1. Stop all applications running in the host server.
2. Turn off the host server.
3. Close any GUI or CLI applications.
4. Power off the RAID system using the power switch.
Technical Support
Related manuals for AE2700
NC200
Able Planet
/
Headphones
Read
BCH100
Abocom
/
Headphones
Read
BCH110
Abocom
/
Headphones
Read
BSH201
Abocom
/
Headphones
Read
BSH202
Abocom
/
Headphones
Read
BSH203
Abocom
/
Headphones
Read
Brands
★
#
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Cisco
HP
LG
Motorola
Panasonic
Sony
Dell
Samsung
Canon
Honeywell
Yamaha
Garmin
Sharp
John Deere
Brother
Apple
Craftsman
GE
NETGEAR
Pioneer
Casio
Maytag
Whirlpool
Kenmore
Nikon
Singer
Bissell
Frigidaire
All brands
New Manuals
ZyXEL Communications ZyXEL G-162 Video Gaming Accessories User Manual
ZyXEL Communications EW103U/A Video Gaming Accessories User Manual
Western Telematic RSM-8 Video Gaming Accessories User Manual
Western Telematic RSM-32DC Video Gaming Accessories User Manual
Western Telematic RSM-32 Video Gaming Accessories User Manual
Western Telematic RSM-16DC Video Gaming Accessories User Manual
Western Telematic RSM-16 Video Gaming Accessories User Manual
Viking Electronics FBI-1A Video Gaming Accessories User Manual
Viking Electronics DVA-500A Video Gaming Accessories User Manual
Viking Electronics DVA-3003 Video Gaming Accessories User Manual
Viking Electronics DVA-2W Video Gaming Accessories User Manual
Viking Electronics DVA- 1003B Video Gaming Accessories User Manual
Full list