Document Outline

• 1. Overview For All Meters
  • 1.1 About the Meters
    • 1.1.1 Display Overview
    • 1.1.2 Key Functions
  • 1.2 Inserting Batteries
    • 1.2.1 Inserting batteries for the first time
    • 1.2.2 Changing batteries subsequently
  • 1.3 Attaching the Belt
  • 1.4 Connecting Peripherals
    • 1.4.1 Probes (pH/Conductivity/DO)
    • 1.4.2 Protective Rubber Boot
• 2. System Setup Mode For All Meters
  • 2.1 About Setup Mode
  • 2.2 Accessing Setup mode
  • 2.3 Setup Selection: System Settings
  • 2.4 Accessing Setup mode when password protection enabled
  • 2.5 Modifying Setup parameters
• 3. Calibration Mode For All Meters
  • 3.1 About Calibration
  • 3.2 About Conductivity/ Resistivity/ TDS/ Salinity Calibration
  • 3.3 Preparing the Meter for Calibration
  • 3.4 Accessing Calibration mode
    • 3.4.1 Accessing Calibration mode when password protection enabled
• 4. Measurement Mode For All Meters
  • 4.1 About Measurement Mode
    • 4.1.1 Accessing functions
  • 4.2 Taking Measurements
    • 4.2.1 Prepare the meter for measurement
    • 4.2.2 Taking a reading
    • 4.2.3 Stable reading indicator
    • 4.2.4 Holding a reading
  • 4.3 Automatic Temperature Compensation (ATC)
    • 4.3.1 Manual Temperature Compensation (MTC)
  • 4.4 Alarm set point (For pH/conductivity/DO)
  • 4.5 Calibration Due (CAL-DUE) Indicator (For pH/conductivity/DO)
• 5. TRANSFERRING AND PRINTING DATA
  • 5.1 CyberComm 600 Data Acquisition Software
  • 5.2 Working with Memory functions – Auto Data Logging
    • 5.2.1 Logging data automatically in the meter’s memory
    • 5.2.2 Storing a current measurement (In IrDA and LED print mode: Applicable to all modes)
    • Viewing stored data
    • 5.2.4 Transferring stored data to the Computer (CyberComm) through IrDA
    • 5.2.5 Transferring stored data to a PC not equipped with infrared receiver.
    • 5.2.6 Transferring stored data to a PC using an USB/ irDA Dongle.
• 6. Technical Specifications
• 7. Accessories
• 8. Warranty & Return Policy
  • 8.1 Warranty
  • 8.2 Return of Goods
  • 8.3 Guidelines for Returning Unit for Repair
• 1. Temperature Setup
• 2. Temperature Calibration
  • 2.1 About Temperature Calibration
  • 2.2 Temperature Calibration for ATC mode
  • 2.3 Temperature Calibration for MTC mode
• 3. Temperature Measurement
• 1. pH Setup
• 2. pH Calibration
  • 2.1 About pH Calibration
  • 2.2 pH buffer group for calibration and auto-recognition
    • 2.2.1 pH Calibration points
  • 2.3 pH Calibration with a Standard Buffer
    • 2.3.1 To start pH Calibration:
  • 2.4 pH Calibration with a User-defined Buffer
  • 2.5 Calibration Report
    • 2.5.1 To View Calibration Report:
  • 2.6 Average Slope Indicator of pH Probe
• 3. pH Measurement Mode
  • 3.1 Resolution of pH Reading
  • 3.2 Indicators in pH measurement screen
• 1. mV Setup Mode
• 2. mV Calibration Mode
  • 2.1 mV Calibration with a Standard ORP Calibration Solution
  • 2.2 Calibration Report
    • 2.2.1 To View Calibration Report:
• 3. mV Measurement Mode
  • 3.1 Indicators in mV measurement mode
• 1. Ion Setup
• 2. Ion Calibration Mode
  • 2.1 About Ion Calibration
  • 2.2 Calibration Report
    • 2.2.1 To View Calibration Report
• 3. Ion Measurement Mode
  • 3.1 Changing unit of measurement
  • 3.2 Indicators in Ion measurement mode
• 1. Conductivity Setup
• 2. Conductivity Calibration Mode
  • 2.1 Conductivity Calibration mode
    • 2.1.1 Conductivity calibration points
  • 2.2 Cell constant
  • 2.3 Normalization Temperature ((C)
  • 2.4 Linear Temperature Coefficient
  • 2.5 Pure Water Coefficient
  • 2.6 To begin Calibration
  • 2.7 Manual Calibration
  • 2.8 Automatic Calibration (For Conductivity Calibration)
  • 2.9 Calibration Report
    • 2.9.1 To View Calibration Report:
• 3. Conductivity Measurement Mode
  • 3.1 Indicators in Conductivity measurement screen
• 1. TDS Setup
• 2. TDS Calibration Mode
  • 2.1 TDS Calibration Report
    • 2.1.1 To View Calibration Report:
• 3. TDS Measurement Mode
  • 3.1 Indicators in TDS measurement mode
• 4. About TDS
  • 4.1 Calculating TDS Conversion Factor
  • 4.2 Calculating Temperature Coefficients
• 1. Salinity Setup
• 2. Salinity Calibration Mode
  • 2.1 Salinity Calibration Report
    • 2.1.1 To View salinity Report:
• 3. Salinity Measurement Mode
  • 3.1 Indicators in salinity measurement mode
• 1. Resistivity Setup
• 2. Resistivity Calibration Mode
  • 2.1 Resistivity Calibration Report
    • 2.1.1 To View Calibration Report:
• 3. Resistivity Measurement Mode
  • 3.1 Indicators in Resistivity measurement mode
• 1. O2 % - DO Saturation Setup
• 2. DO Calibration in % Saturation Mode (with ATC)
  • 2.1 About DO(%) and DO (mg/L) Calibration
  • 2.2 To calibrate 100% saturation
  • 2.3 To calibrate 0% saturation
    • 2.3.1 % DO Calibration Report
    • 2.3.2 To View Calibration Report:
  • 2.4 % Saturation Offset Adjustment
  • 2.5 Set barometer pressure range and barometric pressure units
  • 2.6 Pressure compensation
• 3. Percentage Saturation (%) Measurement Mode
  • Indicators in percentage saturation measurement mode
• 1. O2 mg/L (ppm) – DO Concentration Setup
• 2. DO Calibration in mg/L mode or ppm Concentration mode
  • 2.1 Concentration Calibration Report
    • 2.1.1 To View Calibration Report:
  • 2.2 Set Salinity
    • 2.2.1 Auto Salinity Compensation
• 3. Concentration in Measurement Mode
  • 3.1 Indicators in concentration measurement screen
  • 3.2 Dissolved Oxygen Probe
    • 3.2.1 Dissolved Oxygen Principle
    • 3.2.2 Probe Care
    • 3.2.3 Membrane Housing Replacement
    • 3.2.4 Membrane/O-ring Replacement (Optional Procedure)
    • 3.2.5 Electrolyte Solution