Document Outline

• OPERATOR INSTRUCTIONS & LUBRICATION
  • 20045 Owner/Operator Manual
    • Important Safety Notice
    • Other Notices
    • Introduction
    • Nomenclature
    • Safety Highlights
    • Decals Inside Cab
    • Decals Outside Cab
    • Optional Equipment Decals
    • Operator's Cab
    • Control & Instrument Identification
    • Checks & Services Before Starting Engine
    • Warm-Up & Operational Checks
    • Engine Operation
      • Starting the Engine
      • Cold-Weather Starting Aids
      • Battery-Boosted Starting
      • Normal Engine Operation
      • Stopping the Engine
    • Brake System
      • General
      • Inching Travel
      • Service Brakes
      • Parking Brakes
    • Parking the Handler
    • Steering System
    • Drive Train
    • Boom
    • Leveling the Handler
    • Operating Procedures & Techniques
      • Hydraulic Controls
      • Rated Capacity Charts
    • Attachments
      • Approved Attachments
      • Non-Approved Attachments
      • Carriage/Fork Capacities
      • Other Attachment Capacities
      • Attachment Installation
      • Attachment Operation
        • Fork Positioner
        • Light Material Bucket
        • Mast (6' with 48" or 66" carriage)
        • Swing Forks
        • Slope Pile Carriage
        • Boom Head-Mounted Winch
        • Truss Boom & Truss Boom with Winch
        • Swing Mast
        • Personnel Work Platform
    • Lubrication & Routine Maintenance
    • Recommended Lubricants & Capacities
    • Torque Chart
    • Obtaining Hydraulic Oil Sample for Analysis
    • Moving Handler in Emergency
      • Moving Short Distances
      • Moving Longer Distances
      • To Activate Tow Bypass
      • To Release Parking Brake
      • To Restore Parking Brake
    • Hand Signals
• HYDRAULIC SYSTEM
  • 9108-9027 Hydraulic Schematic
  • BLN9939 Sundstrand Sauer Rear Drive Motor Service Manual
    • Minor Repair & Replacement
  • RA64-789-S Hydraulic Gear Pumps Service Manual
    • Preparation for Disassembly
    • Disassembly of Pump
    • Parts Inspection
    • Pump Reassembly
    • Break-In Procedure
      • Output Chart
      • Illustration
  • 81-460-047 Mico Hydraulic Power Brake Valve Service Manual
    • System Schematic
    • Representative Performance Data
    • Description & Operation of Power Brake Valve
    • External Dimensional Views
    • Installation of Power Brake Valve
    • Cross Sectional Views of Three Power Brake Valve Designs
    • Specification Chart
    • Primary Cup Design
    • Teflon Seal Design
    • Sliding Piston Design
    • Service Diagnosis
    • Bleeding
• AXLES
  • 8HD90 Auburn Gear Planetary Gear Drive Service Manual
    • Illustration
    • Identification
    • Disassembly of Power Wheel
    • Assembly of Power Wheel
    • Carrier Assemblies
    • Lubrication Recommendations
    • Specifications
    • RTV Sealing Compound
    • Towing Vehicle
    • To Disengage Power Wheel
    • Storage
    • Parts List
  • FMM9D Meritor PRA 352 Series Planetary Axles
    • Service Notes
    • Exploded Views
    • Table of Contents
    • Section 1
    • Section 2
    • Section 3
    • Section 4
    • Section 5
    • Section 6
• TRANSMISSION
  • 29707 Hydrostatic Drive Performance Checks Manual (Ver 2)
    • Disclaimer
    • Introduction
    • Important Safety Notice
    • Required Tools
    • General Warning Information
    • Section I Hydraulic Oil Reservoir
    • Section II Park Brake
    • Section III Hydraulic Filter Condition
    • Section IV Engine Speed
    • Section V Charge Pressure
    • Section VI Control Pressure
    • Section VII Inching
    • Section VIII Front Motor Begin Point
    • Section IX Hydrostatic Transmission Pressure
    • Section X Machine Operation
    • Section XI Hydraulic System Pressures
• MISCELLANEOUS
  • 29906 532/534 Boom Maintenance
    • Introduction
    • Special Note on Boom Cables
    • Safety
    • Note on Using the Manual
    • Nomenclature
    • Boom Adjustment
    • Bearing Pad Removal
    • Bearing Pad Installation
    • Separating Boom Sections
    • Assembling Boom Sections 1, 2, & 3
    • Boom Cables
    • Tilt & Auxiliary Circuit Hydraulic Hoses
    • Auxiliary Electric Cable
    • Crowd Cylinder Removal & Installation
    • Fastener Torque Chart, English Bolts
    • Fastener Torque Chart, Metric Fasteners
    • Hose Fitting Torque Chart
    • Boom Drawings
  • 29813 Implement Circuit Performance Checks
    • Introduction
    • Safety
    • Note on Using the Manual
    • Hydraulic Oil Reservoir
    • Hydraulic Filter Condition
    • Engine Speed
    • Charge Pressure (Pilot Pressure)
    • Steering Circuit
    • Main Control Valve Pump Relief
    • Tilt Circuit Relief Valves
    • Crowd Circuit Extend Relief Valve
    • Auxiliary Circuit Relief Valves
    • Service Brake Valve
    • Cycle Times for Functions
  • 29903 Kenhar User Fork Wear Standards
  • 0009 Rim & Wheel Safety Manual
  • 9134-9012 Electrical Schematic
  • 28902 Char-Lynn Steering Control Units Troubleshooting Guide
  • F114004 Donaldson Cyclopac Service Procedure