AML56 Series Guide
User manual for AML56 Series
Table of contents
Document Outline
- Content
- 1.0 Introduction
- 2.0 Recommended Service Tools
- 3.0 Load Cell Assemblies and General Specifications
- 4.0 Applications
- 4.1 Air Pressure Transducer
- 4.1.1 Installation Procedure
- 4.1.2 Slip Spring/Torque Arm Air Suspension
- 4.1.3 Technical Specifications
- 4.2 Underbody Load Cell Mounts
- 4.2.1 Underbody Mounting Brackets
- 4.2.2 Underbody Mounting of Load Cells
- 4.2.3 Stress Concentrations and Frame Reinforcing
- 4.2.4 Underbody Load Cell Mounting
- 4.3 Kingpin Plate Mounts
- 4.3.1 Skid Plate Preparation
- 4.3.2 Trailer Body Preparation
- 4.3.3 Installation Procedure
- 4.4 Equalizer Hanger Mounts
- 4.4.1 Preparation
- 4.4.2 Assembly
- 4.5 Fixed 5th Wheel Mounts
- 4.5.1 Installation Procedure
- 4.6 Hinge and Hoist Pivot Pin Installation
- 4.6.1 Installation Procedure
- 4.6.2 Hinge Bar and Lift Cylinder Pin
- 4.7 Body Rest Mounts
- 4.7.1 Installation Procedure
- 4.8 Trunnion Load Pin Installation
- 4.9 Sandshoe Load Pin for Landing Gear
- 4.9.1 Installation Procedure
- 4.10 Single Point Suspension Clamp Load Cell Mount Installation
- 4.11 PL9710 and PL9740 Output Ports
- 5.0 Service and Troubleshooting
- 5.1 System Maintenance
- 5.2 Calibration
- 5.3 Sensor Maintenance
- 5.3.1 Load Cells
- 5.3.2 Load Pins
- 5.3.3 Visual Inspection
- 5.4 Cables and Connectors
- 5.4.1 Cables
- 5.4.2 Connections
- 5.4.3 Truck/Trailer Connector
- 5.5 System Troubleshooting
- 5.5.1 Error Messages
- 5.5.2 Test
- 5.5.3 Isolate
- 5.5.4 Calibration
- 5.6 Cal Factors
- 5.7 Application-Specific Service Notes
- 5.7.1 Spring-mounted Load Cells
- 5.7.2 Trunnion Load Pins
- 5.8 Lift-to-Weigh Program
- 5.8.1 Air Pressure Transducers
- 5.9 Connector Pin-outs, Color Codes
- 5.10 .Error Messages
- 5.11 Test Mode
- 5.11.1 Recording Test Numbers
- 6.0 Appendix
- 6.1 Bolt Torque Values
- 6.2 Spring Bolt Mountings
- 6.3 Welding Specifications
- 6.3.1 Preparation
- 6.3.2 Installation Procedure
- 6.3.3 Inspection
- 6.3.4 Bolt Torque Verification
- 6.4 Transmitter Installation and Cabling
- 6.4.1 Transmitter location
- 6.4.2 Mounting the transmitter
- 6.4.3 Installing the Cables
- 6.4.4 Power Access
- 6.5 Equalizer Hanger Modification
- 6.6 Hinge Bar Installation Drawing
- 6.7 Underbody Load Cell Chassis and Body Brackets Drawings
- 6.8 5th Wheel Mounts for Pole Trailers and Dump Trailers
- 6.9 Trailer Rear Hanger Assembly
- 6.10 PL9710 Indicators with PL9774 Limit Setpoint Option
- 6.10.1 System Configurations
- 6.10.2 Limit Module Connections
- 6.10.3 Program Setup
- 6.10.4 Operation
- Hardware Warranty Statement
Related manuals for AML56 Series
New Manuals
- ZyXEL Communications ZyXEL G-162 Video Gaming Accessories User Manual
- ZyXEL Communications EW103U/A Video Gaming Accessories User Manual
- Western Telematic RSM-8 Video Gaming Accessories User Manual
- Western Telematic RSM-32DC Video Gaming Accessories User Manual
- Western Telematic RSM-32 Video Gaming Accessories User Manual
- Western Telematic RSM-16DC Video Gaming Accessories User Manual
- Western Telematic RSM-16 Video Gaming Accessories User Manual
- Viking Electronics FBI-1A Video Gaming Accessories User Manual
- Viking Electronics DVA-500A Video Gaming Accessories User Manual
- Viking Electronics DVA-3003 Video Gaming Accessories User Manual
- Viking Electronics DVA-2W Video Gaming Accessories User Manual
- Viking Electronics DVA- 1003B Video Gaming Accessories User Manual